西门子伺服电机刹车片磨损维修 免费检测

西门子伺服电机维修故障范围：上海仰光电子科技有限公司维修故障：西门子伺服电机磁铁爆钢维修、西门子伺服电机磁铁脱落维修、西门子伺服电机卡死转不动维修、西门子伺服电机编码器磨损维修、西门子伺服电机码盘/玻璃盘磨损破裂维修、西门子电机发热发烫维修、西门子电机进水维修、西门子电机运转异常维修、西门子伺服电机高速运转响声维修、西门子电机噪音大维修，西门子伺服电机刹车失灵维修、西门子伺服电机刹车片磨损维修、西门子电机速正常高速偏差维修、

坐标轴进给时振动
   应检查电机线圈、机械进给丝杠同电机的连接、伺服系统、脉冲编码器、联轴节、测速机。

二、五、出现NC错误报警
NC报警中因程序错误，操作错误引起的报警。如FANUC6ME系统的Nc出现090.091报警，原因可能是：
1、主电路故障和进给速度太引起;
2、脉冲编码器不良;
3、脉冲编码器电源电压太(此时调整电源15V电压，使主电路板的+5V端子上的电压值在4.95-5.10V内);
4、没有输人脉冲编码器的一转信号而不能正常执行参考点返回。

三、六、伺服系统报警
     我们在解决伺服系统故障的时侯，经常会碰到如下的报警号，例如FANUC 6ME系统的416、426、436、446、456伺服报警;STEMENS 880系统的1364伺服报警;STEEMENS 8系统的114、104等伺服报警，这时我们应该先检查：
1、轴脉冲编码器是否存在反馈信号断线、短路和信号丢失等，利用示渡器检测一下A、B相一转信号，看其是否正常;
2、有可能编码器出现内部故障，造成此信号无法正常接收，检查编码器是否受到污染、太脏、变形等。

1FK6042-6AF71-1AB0维修   1FK60426AF711AB0

1FK6042-6AF71-1AG0维修   1FK60426AF711AG0

1FK6042-6AF71-1AH0维修   1FK60426AF711AH0

1FK6042-6AF71-1EA0维修   1FK60426AF711EA0

1FK6042-6AF71-1EG0维修   1FK60426AF711EG0

1FK6042-6AF71-1EG2维修   1FK60426AF711EG2

1FK6042-6AF71-1EH0维修   1FK60426AF711EH0

1FK6042-6AF71-1GB2维修   1FK60426AF711GB2

1FK6042-6AF71-1GG0维修   1FK60426AF711GG0

1FK6042-6AF71-1GH2维修   1FK60426AF711GH2

1FK6042-6AF71-1SA0维修   1FK60426AF711SA0

1FK6042-6AF71-1SG0维修   1FK60426AF711SG0

1FK6042-6AF71-1SG2维修   1FK60426AF711SG2

1FK6042-6AF71-1SH0维修   1FK60426AF711SH0

1FK6042-6AF71-1TA0维修   1FK60426AF711TA0

1FK6042-6AF71-1TB0维修   1FK60426AF711TB0

1FK6042-6AF71-1TG0维修   1FK60426AF711TG0

1FK6042-6AF71-1TH0维修   1FK60426AF711TH0

1FK6060-6AF71-1AA2维修   1FK60606AF711AA2

1FK6060-6AF71-1AB0维修   1FK60606AF711AB0

1FK6060-6AF71-1AG0维修   1FK60606AF711AG0

1FK6060-6AF71-1AH0维修   1FK60606AF711AH0

1FK6060-6AF71-1EA0维修   1FK60606AF711EA0

1FK6060-6AF71-1EG0维修   1FK60606AF711EG0

1FK6060-6AF71-1EH0维修   1FK60606AF711EH0

1FK6060-6AF71-1TG0维修   1FK60606AF711TG0

1FK6063-6AF71-1AA2维修   1FK60636AF711AA2

1FK6063-6AF71-1AB0维修   1FK60636AF711AB0

1FK6063-6AF71-1AB2维修   1FK60636AF711AB2

1FK6063-6AF71-1AG0维修   1FK60636AF711AG0

1FK6063-6AF71-1AG2维修   1FK60636AF711AG2

1FK6063-6AF71-1AH0维修   1FK60636AF711AH0

1FK6063-6AF71-1AH2维修   1FK60636AF711AH2

1FK6063-6AF71-1EG0维修   1FK60636AF711EG0

1FK6063-6AF71-1EH0维修   1FK60636AF711EH0

1FK6063-6AF71-1GH2维修   1FK60636AF711GH2

1FK6063-6AF71-1SA0维修   1FK60636AF711SA0

1FK6063-6AF71-1TB0维修   1FK60636AF711TB0

1FK6063-6AF71-1TG0维修   1FK60636AF711TG0

1FK6063-6AF71-1TH0维修   1FK60636AF711TH0

1FK6080-6AF71-1AG0维修   1FK60806AF711AG0

1FK6080-6AF71-1TH0维修   1FK60806AF711TH0

1FK6083-6AF71-1AB0维修   1FK60836AF711AB0

1FK6083-6AF71-1AG0维修   1FK60836AF711AG0